3-276-523-11(1) Setting the Code Follow the steps 1 and 2 below for each component you plan to use with the Commander. Searching for the Correct Code You can find a code number available for a component that doesn't have one in the supplied "Component code numbers." Before starting the Search function Set each component to the following status so that the Search function works effectively. TV, DVD Home Theater: Power-on Other components: Power-off * If any of these components are assigned to any of the Component Select buttons, you can set a component code using the Search function. SET TV VCR CBL POWER Remote Button Descriptions DVD Operating a DVR (Digital video recorder) 2 To change the input mode. 3 and qd To change the channel. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER). 8 To turn on the display. 9 To bring up Master Guide. q; To clear the setting. To exit the setting menu. qg CH+: Channel up . (*PAGE+) Page up. CH­: Channel down. (*PAGE­) Page down. qh To operate JUMP or CHANNEL RETURN qj To call up "Tivo" menu. qk To call up the MENU display. ql To move the cursor upward, downward, to the left, to the right or to enter the selection. wa N: To play. m: To rewind. M: To fast-forward. zREC: To record, press N while pressing zREC. x: To stop. X: To pause. .: To proceed to the previous location. >: To proceed to the next location. : To operate " Flash ­." : To operate " Flash +." ws D: (*Live TV) To bring up Master Guide. A: (*REPLAY) To replay. Or to go into REC/REVIEW mode during play. (After about 5-second rewind, replay begins.) wd PAGE+ : (*THUMBS+) To select the desired recorded program. (It is necessary to have recorded the desired program.) PAGE­ : (*THUMBS­) To select the desired recorded program. (It is necessary to have recorded the desired program.) wf (*LIST) To call up the title of the recorded program. Operating a digital satellite receiver 2 To switch the output of the digital satellite receiver to the TV. (When you connect a TV cable or antenna to the receiver, the output switches between a TV and SAT program.) 3, 4 and qd To change the channel. For example, to change to channel 5, press 0 and 5 (or press 5 and ENTER). 8 To turn on the display. 9 To bring up the Master Guide. q; To exit the mode. qf To call up the DISH menu. qg Channel up: + Channel down: ­ qh To tune to the last tuned station. qj To call up the PVR menu. qk To call up the MENU display. ql To move the cursor upward, downward, to the left, to the right, or to enter the selection. w; To bring up the Station Index. wa N: m: M: zREC: To play. To rewind. To fast-forward. To record, press N while pressing zREC. x: To stop. X: To pause. .: To proceed to the previous location. >: To proceed to the next location. : Replay : Advance A: RED button B: GREEN button C: YELLOW button D: BLUE button PAGE+: Page up. PAGE-: Page down. To call up the title of the recorded program. To use the "FAVORITE" function. Operating a DVD Home Theater 2 To change the input mode. 3 and qd Number buttons: To set items selected on the screen. 4 To select numbers 10 and above. 6 VOL+: AMP volume up VOL­: AMP volume down 7 AMP volume muting 8 To show the current play status on the screen. 9 To change the sound. q; To return to the previous screen. qf To switch the subtitle. qg CH+: Tuner + CH­: Tuner ­ qk To call up the MENU. ql To move the cursor upward, downward, to the left, to the right, or to enter the selection. w; AMP menu To play. To rewind. To fast-forward. To record, press N while pressing zREC. x: To stop. X: To pause. .: To proceed to the previous location. >: To proceed to the next location. : To operate " Flash ­." : To operate " Flash +." ws B: open/ close A: To call up the setup menu. C: Disc skip D: To display the Top Menu. wg To call up MEMORY. wa N: m: M: zREC: Remote Commander RM-V210 Operating Instructions Manual de instrucciones (parte posterior) © 2007 Sony Corporation Printed in China Step 1: Entering the Code Number 1 See the supplied "Component code numbers", and find the four-digit code number for the desired component. If more than one code number is listed, use the number that's listed first. For example, if you're setting up a Sony TV, you would use the code number 8201. If your component isn't listed, see "Searching for the Correct Code." 2 Press SET more than two seconds. The SET indicator lights up. 3 Press the button of the component that you want to set up. The SET indicator lights up. 2 SET TV VCR CBL POWER DVD 1 3 2 Component code numbers / Números de código de componentes English DVR (digital video recorder), SAT (digital satellite receiver), Cable box, TV, DVD Home Theater, DVD and VCR The following tables show brand names and their corresponding code numbers. DVR (Digital Video Recorder)/ DVR (Videograbadora digital) Brand Sony Humax Panasonic Philips Pioneer ReplayTV Tivo Toshiba SET indicator SET TV VCR CBL POWER DVD General 1 2 5 8 0 INPUT 1 4 7 VOL 2 5 8 0 INPUT PIP 3 6 9 ENTER 3 6 9 ENTER 3 4 5 CH 4 3 4 7 VOL 1 4 7 VOL 2 5 8 0 INPUT PIP 3 6 9 ENTER CH SLEEP PIP INFO MUTING RECALL SLEEP CH INFO English MUTING A B PAGE GUIDE RECALL C D SLEEP 1 Press SET more than two seconds. The SET indicator lights up. RECALL MENU INFO For the customers in the U.S.A. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Installing the Batteries Before replacing the batteries, have new ones ready beforehand. Slide open the battery compartment and insert two size AA (R6) batteries (not supplied). Be sure to line up the + and ­ on the batteries with the + and ­ on the battery compartment. MUTING 2 Press the Component Select button for the desired component. The SET indicator lights up. 3 Press CH + or CH ­ and POWER in turn until the component reacts as follows: TV, DVD Home Theater: Powers off Other components: Powers on Press CH + to go to the next code number. Press CH ­ to go back to the previous code number. The SET indicator flashes once after the numbers have turned one cycle. One cycle means, for example, that the commander finishes searching all the component code numbers allocated to the component. 4 Press ENTER. The SET indicator and the Component button turn off. If the SET indicator flashes five times before turning off, it means that the setup is incomplete. Start over from Step 3. If the component does not operate properly, repeat steps 1 to 4 and search for another code. If you still cannot get the Commander to work properly, see "Troubleshooting." LIST FAV OK EXIT TOOLS 1 To set up the Commander, press SET more than two seconds. 6 Volume up: + Volume down: ­ 7 To mute the volume on a TV or a DVD Home Theater. qa To turn on and off the power of the selected component. qs Component select buttons. Press to select a component to operate. Tivo Code No. 3201, 3205, 3206 3202, 0413 -- 3202, 0412 0413 -- 3201, 3202 0413 ReplayTV Code No. -- -- 3203 -- -- 3203, 3204 -- -- Español DVR (Videograbadora digital), SAT (Sintonizador de recepción vía satélite digital), adaptador para cablevisión, Televisor, Sistema de cine doméstico en DVD, DVD (reproductor de discos DVD) y Videograbadora Las tablas que se presentan a continuación muestran las marcas y los números de código correspondientes. ws wd wf wg To set a Component Code (see the instruction manual for details) Para introducir un código de componente (consulte los detalles en el manual de instrucciones) Cable box/Adaptadores para cablevisión Brand Sony ABC Adelphia Advanced Newhouse Altrio Americast Atlantic Broadband Bell South Blue Ridge Brigth House Cablevision Charter Comcast Cox General Instrument Gnc Hamlin Illico Jerrold Memorex Motorola NET Oak Pace Panasonic Paragon Philips Pioneer Pulsar Regal Rodgers Runco Scientific Atlanta Seren Sigecom Susquehanna Time Warner Tocom Toshiba Videotron Wideopenwest Zenith Code No. 3101 9405 3107, 3110 3107 3107 3105 3107 3105 3107 3107 3107 3107 3107 3107 3103, 9002, 9003, 9004, 9005, 9006, 9007, 9008, 9018, 9022, 9043, 9044 3105 9022, 9023, 9024, 9025, 9026 3107 3103, 9002, 9003, 9004, 9005, 9006, 9007, 9008, 9018, 9022, 9043, 9044 3106 3103, 3110, 3111 9042 9027, 9028, 9029 3107 9019, 9020, 9021 3106 3104 3107, 9014, 9015 3106 9022, 9023, 9024, 9025, 9026 3107 3106 3102, 3107, 3108, 3109, 9009, 9010, 9045, 9046 3107 3107 3107 3107 9016, 9017, 9043 3106 3107 3105, 3107 3105, 3106, 9013 SET SET SET c TV VCR CBL DVD c Code No. c ENTER 1 2 TV VCR CBL DVD SET 4 Press the Number buttons to enter the four-digit component code number. 5 Press ENTER. The SET indicator turns off. If the SET indicator flashes five times before lighting up, it means that the setup is incomplete. Confirm the component code number and start over from Step 4. ENTER SAT(Digital satellite receiver)/ SAT(Sintonizador de recepción vía satélite digital) About tactile dots The number 5 button, the N button and CH+ each have a tactile dot for convenient use. Specifications Operating a DVD 2 To change the input mode. 3 and qd Number buttons : To set items selected from the screen. 4 To select numbers 10 and above. 8 To show the current play status on the screen. 9 To bring up the Master Guide. q; To return to the previous screen. qd To enter the setting. To set items selected from the screen. qf To switch the subtitle. qg CH+: Channel up. CH­: Channel down. qh To select a deck. qj To switch the subtitle. qk To display the DVD menu. ql To move the cursor upward, downward, to the left, to the right, or to enter the selection. w; To call up the "TOOLS" menu. wa N: To play. m: To rewind. M: To fast-forward. zREC: To record, press N while pressing zREC. x: To stop. X: To pause. .: To proceed to the previous location. >: To proceed to the next location. : To operate " Flash ­." : To operate " Flash +." ws B: open/ close D: To display the Top Menu. A: To call up the setup menu. wd PAGE+: To select DVD deck. PAGE-: To select HDD deck. wf To display the title menu. Operable distance Power requirements Battery life Dimensions Mass Approx. 7 m (23 ft) (varies depending of the component of each manufacturer) Two size AA (R6) batteries (not supplied) Approx. 1 year (varies depending on frequency of button use - up to approx. 300 times per day.) Approx. 53 × 220 × 29 mm (w/h/d) (2 1/8 × 8 3/4 × 1 3/16 in.) Approx. 108 g (3.8 oz.) (not including batteries) Brand Sony DirecTV Dish Network General Electric Hitachi Hughes Humax JVC Magnavox Panasonic Philips Proscan RCA Samsung Sylvania Toshiba Usdigital DirecTV Code No. 3001,3011,3012 3013, 3017, 3018, 3019, 3023, 3024 -- 3019 3005 3004 3402 -- 3018 3003 3018 3002, 3007, 3019 3002, 3007, 3019, 3021 3017, 3022 -- 3006 -- Dish Network Code No. -- -- 3010, 3014, 3025 -- -- -- -- 3010, 3014 -- -- -- -- -- -- -- -- -- Digital TV Tuner Code No. -- -- -- -- -- -- -- -- -- -- -- -- -- 3404 3403 -- 3401 Note on the VOL+/- and MUTING buttons The Commander controls or mutes the TV's volume when you select a visual component. The Commander outputs the signals to control or to mute a TV or DVD Home Theater's own volume when you have set one of these components. When to replace the batteries Under normal conditions, batteries will last up to one year. If the Commander does not operate properly, the batteries might be worn out. Replace the batteries with new ones. If the code setting is not finished properly If you do not input anything into the Commander within 20 seconds between each step, or if you press SET while setting the component code, the setup procedure will be canceled. Start over from Step 2. * This key corresponds to Tivo service or the replay service. Refer to its instruction manual for details. Notes · Replace both batteries with new ones. · Do not take more than 3 mi ...