Floor stand Support de base Bodenständer Supporto per display Vloerstandaard Soporte para colocar en el suelo PDK-FS05 Operating instructions Mode d'emploi Bedienungsanleitung Istruzioni per l'uso Gebruiksaanwijzing ucciones Manual de instrucciones 2 Ja Floor stand Support de base Bodenständer Supporto per display Vloerstandaard Soporte para colocar en el suelo PDK-FS05 Operating instructions Mode d'emploi Bedienungsanleitung Istruzioni per l'uso Gebruiksaanwijzing ucciones Manual de instrucciones 3 Ja 1 3 A A B 2 A 4 Ja B 5 4 5 Ja 6 1 2 2 1 2 2 1 8 7 1 9 6 Ja 10 1 11 12 2 13 1 2 7 Ja Ja B 54 960 206 860 8 210 40 40 (179) 478 373 299 59 471±50 760 A Thank you for buying Pioneer's product. Please read through the Operating Instructions to learn how to operate your model safely and properly. Please be advised to keep the Operating Instructions in your place for future reference. Cautions This product is a floor stand for plasma displays (PDP-506XDE / PDP-506FDE / PDP-506HDG / PDP-436XDE / PDP-436FDE / PDP436HDG) from Pioneer. Use with other model is capable of resulting in instability causing possible injury. For further information, please contact the store where you purchased your display. Do not install or modify the product other than specified. Do not use this stand for a plasma display other than those designated and do not modify it or use it for other purposes. Improper installation is extremely dangerous because it may result in it falling over or other accident. IMPORTANT NOTICE Record the model number and serial number of this equipment below. Model No. PDK-FS05 Serial No. Keep this number for future use. WARNING To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the D3-4-2-1-7a_A_En equipment. Installation Location · When selecting the location in which the stand is to be placed, be sure to select a location with a surface sufficiently strong to bear the weight of the stand and plasma display (Product weight is listed on page 15). · Make sure to place it in a level and stable location. · Depending on the type of surface on which the stand is placed, the casters may leave marks on the surface, and this should be taken into consideration when selecting the place in which the stand is to be placed. · Do not install it outdoors, at a hot spring, or near a beach. · Do not install the stand where it may be subjected to vibration or shock. Installation ¶ Consult your dealer if you encounter any difficulties with this installation. ¶ Pioneer is not liable for any damage resulting from improper installation, improper use, modification, or natural disasters. Contents Cautions ............................................................................. 9 List of parts and equipment included ........................... 10 Installation and assembly instructions ......................... 11 Moving the stand and display ....................................... 14 Preventing equipment from falling over....................... 14 Specifications .................................................................. 15 Dimensions diagram ....................................................... 15 Assembling and Installation · Assemble the stand in accordance with the assembly instructions and securely attach all screws at the designated locations. There have been cases where unforeseen accidents such as the equipment breaking or falling over occurred after the installation of the display because the stand was not installed as instructed. · The display must always be installed by two or more people to assure it is installed safely. · Before installation, turn off the power for the display and peripheral devices then remove the power cord plug from the power outlet. After Installation · Never lean on the plasma display or apply heavy pressure to the stand. · Note that while the stand is fitted with casters to make it easily movable, when moving the stand you should always follow the instructions given on page 14 under "Moving the stand and display". · Because of the nature of glass, the application of shocks to the edges can make it easy for the glass to break, and the application of any such shocks should therefore be strictly avoided. Due care should also be taken to keep children from bumping into the edges, as doing so might result in injury. · Prevent accidents caused by the product falling over by taking reliable measures to prevent it from falling over (see page 14). CAUTION This symbol refers to a hazard or unsafe practice which can result in personal injury or property damage. 9 En English List of parts and equipment included Be sure to check that all the parts and equipment listed below have been included before beginning to assemble your stand. · Note that a Philips screwdriver (not included) is required for assembly. · Center support column x1 · Base x1 · PDP bracket x1 · Glass panel x1 · Glass stays (x2, one left and one right) · Support column covers (x2, one left and one right) Caution The glass panel should be kept in its packing box until you are ready to attach it to the stand to guard against breakage. · Long support legs x2 · Short support legs x2 · Cable cover x1 (for attachment to support column) · Cap x1 (Please refer to the table for Procedure 3 on page 11 for usage.) · Short hexagonal bolts (M8 x 16 mm: black) x12 · Hexagonal wrench x1 (Opposite side 6 mm for M8 use) · Cable clamps x4 · Middle hexagonal bolts (M8 x 35 mm: black) x4 · Screws (M4 x 10 mm: silver) x4 · Operating instructions (This document) x1 Floor stand Support de base Bodenständer Supporto per display Vloerstandaard Soporte para colocar en el suelo PDK-FS05 · Long hexagonal bolts (M8 x 60 mm: silver) x2 · Screws (M4 x 10 mm: black) x2 Operating instructions Mode d'emploi Bedienungsanleitung Istruzioni per l'uso Gebruiksaanwijzing ucciones Manual de instrucciones 10 En Installation and assembly instructions (Stand shown below is a 43-inch display stand) 1 Slide center support column into brackets on the base and use short hexagonal bolts to fix it into place (4 locations). Locations of holes on center support column for attachment of PDP bracket Upper holes Upper holes Center support column Middle holes Middle holes Short hexagonal bolts (M8 x 16 mm: black) Base Slide into brackets Lower holes Lower holes 3 Attach the long support legs or short support legs to the PDP bracket with the short hexagonal bolts (4 locations). Table of parts included with each plasma display Plasma Display Location of speaker Support legs attachment method Support legs Plasma display attachment use top hexagonal bolts Plasma display attachment use bottom hexagonal bolts Unused Support legs parts Hexagonal bolts PDP-506XDE PDP-506FDE PDP-506HDG Side PDP-436XDE PDP-436FDE PDP-436HDG Side Under One body type plasma display ­ A Short ×2 Middle ×2 A Short ×2 Middle ×2 B Long ×2 Middle ×2 B Long ×2 Long ×2 2 Use short hexagonal bolts to attach PDP bracket to center support column (bolts must be screwed in four locations). The bracket may be screwed into the upper holes, middle holes, or lower holes of the center support column to adjust the height of the display. The middle holes are designed to be used for standard installation. PDP bracket Used parts Middle ×2 Long ×2 Long ×2 Middle ×2 Long ×2 Long ×2 Middle ×2 Short ×2 Long ×2 Middle ×2 Short ×2 Middle ×2 Note Be sure to carefully store the unused support legs, the bolts, the hexagonal wrench, and the Operating Instructions together. Short hexagonal bolts (M8 x 16 mm: black) A When installing speakers at the sides of the plasma display Use the short support legs. Use the hexagonal wrench included with the stand to do so. Slide grooves into place Short support legs Short hexagonal bolts (M8 × 16 mm: black) Short support legs Slide grooves into place PDP bracket 11 En English Installation and assembly instructions B When installing speakers below the plasma display or one body type plasma display 5 Use the middle or the long hexagonal bolts to fix the plasma display to the support legs (4 locations). Please install starting with the bolts on the top. When installing the PDP-506XDE / PDP-506FDE / PDP506HDG / PDP-436XDE / PDP-436FDE / PDP-436HDG Use the following bolts to fix it with the hexagonal wrench. Top .................. Middle hexagonal bolts (M8 x 35 mm: black) Bottom ............ Middle hexagonal bolts (M8 x 35 mm: black) Middle hexagonal bolts (M8 x 35 mm: black) Use the long support legs. Use the hexagonal wrench included with the stand to do so. Long support legs Short hexagonal bolts (M8 × 16 mm: black) Long support legs Slide grooves into place PDP bracket Caution The types of plasma displays which may be used with the stand differ depending on the length of the support legs attached to the PDP bracket, so you should check to see if the display to be attached is compatible before proceeding. Middle hexagonal bolts (M8 x 35 mm: black) 4 Attach plasma display to support legs. Fit the stand's support columns to the bottom of the plasma display as indicated by the arrows, then slowly insert them vertically. Be extremely careful not to insert the support legs of the stand into any part of the plasma display other than the stand insertion slots. Note that doing so might damage the plasma display panel or its ports or result in the warping of the stand. If the plasma display is fitted with handles, it is usually best to hold the display by its handles when attaching it to the support legs. Line up the support legs with the bottom of the plasma display as indicated in the accompanying diagram. If speakers are to be installed at the sides or the bottom of the plasma display, they should be attached at this phase. See the installation instructions provided with your speakers for instructions on how to install them. When installing the one body type plasma display Use the following bolts to fix it with the hexagonal wrench. Top .................. Long hexagonal bolts (M8 x 60 mm: silver) Bottom ............ Middle hexagonal bolts (M8 x 35 mm: black) Long hexagonal bolts (M8 x 60 mm: silver) Caution Be sure to work with at least one other person when attaching the display. Be careful not to allow your fingers get caught between the display and support legs. If the PDP bracket has been placed into the upper bracket holes and speakers are to be installed below the plasma display or one body type plasma display, care must be taken to ensure that the display is firmly supported as its position will be higher. Middle hexagonal bolts (M8 x 35 mm: black) 12 En Installation and assembly instructions 6 Attach left and right glass stays to support column. 1 Insert the glass stays into the holes provided, pushing them all the way into the holes so that they point slightly downwards. 2 Press down on the tips of the glass stays to lower them and fit the indentations into frames. Indentation Frame 2 2 Fix it with the screws (M4 x 10 mm: black) (2 locations: left and right). Frame Glass stay 1 2 Philips screwdriver 1 Side with the rubber guard is the upper side. Base Glass stays may be inserted into the upper, middle, or lower holes to adjust the height of the glass panel (The middle holes are designed to be used for standard installation). Glass stay (left) Be sure to use the screws to fix the glass panel into place. Note that failing to do so could cause the glass panel to fall off if you come into contact with Caution it and result in the panel breaking. 8 Place equipment onto glass panel and connect equipment to display. Place the equipment to be connected to the display onto the glass panel and then connect the equipment to the display. Note that the glass panel and base are designed to be able to withstand loads of up to only 20 kilograms (44.1 lbs), and that the weight of the equipment placed onto the glass panel should never exceed this limit. Upper holes Middle holes Glass stay (right) Lower holes Note When a video deck is placed on the glass panel, there may be times when the video deck interferes with the plasma display and causes distortion in the picture depending on the place of the video deck or on other conditions. If this happens, place the video deck on the base instead to avoid interference. 7 Attach the glass panel to the glass stays. 1 Place the glass panel on top of the glass stays. 9 Attach cable cover. Fit the cable cover into the center support column. Note The glass panel should be installed with the warning label facing upwards. Note Be careful when doing so not to allow cables to get caught between the cable cover and the cable insertion slots. Glass panel Cable cover Caution label 13 En English Support column Installation and assembly instructions Moving the stand and display When moving the ...