SRU 5030/87 GB Instructions for use 4 I Instruzioni per l'uso 11 Instrucciones de manejo 18 E P Manual de utilização 25 Od GR 32 40 48 55 RU Návod k pouzití Instrukcja obslugi CZ PL Quick, Clean & Easy Setup www.philips.com/urc Instructions for use Contents 1. 2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installing the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Inserting the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Testing the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Setting the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 Keys and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8 Extra possibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Adjusting device selection (Mode keys) . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Adding a function to the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Restoring the original remote control settings . . . . . . . . . . . . . . . . . . . . . 9 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Need help? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Code list of all brands / equipment . . . . . . . . . . . . . . . . . . . . . . . . . . 62-78 Information to the Consumer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 English 4 3. 4. 5. 6. 1. Introduction Congratulations on your purchase of the Philips SRU 5030 universal remote control. After installing the remote control you can operate a maximum of 3 different devices with it:TV, DVD player/recorder and VCR. You can find information about how to prepare this remote control for use in the chapter `Installing the remote control'. 2. Installing the remote control Inserting the batteries 1 Press the cover inwards and slide it in the 2 3 direction of the arrow. Place two AAA type batteries into the battery compartment, as shown. Slide the cover back and click it firmly into place. Note: If the mode keys (TV, DVD and VCR) blink four times after every key press, the remote control is indicating that its batteries are running low. Replace the old batteries with two new AAA batteries. Testing the remote control The remote control has been programmed to operate most Philips devices. Because the SRU 5030 may use different signals for each brand and even for different models of the same brand, it is advisable to test whether your device responds to the SRU 5030.The example below (TV) instructs you how to do this.You can repeat the same steps for other devices (DVD player/ recorder and VCR) which you want to operate using the SRU 5030. Example of TV: 1 Turn your TV on manually or use the original remote control. Tune to channel 1. 2 Press the TV key to select TV. Press the key until it lights up. ­ If the key does not light up, check whether the batteries are properly inserted (see `Inserting the batteries'). Instructions for use English 5 3 ­ Check whether all the keys are working. For an overview of the keys and their functions see `3. Keys and functions'. If the TV responds as it should to all of the key commands the SRU 5030 is ready for use. If the device does not respond at all or not to all of the key commands, follow the instructions under `Setting the remote control', or for online setup go to: www.philips.com/urc. · Setting the remote control This is only necessary if your device does not respond to the SRU 5030. If that is the case, the SRU 5030 does not recognize the brand and/or model of your device and you need to program the remote control to do so. The example below (TV) instructs you how to do this.You can repeat the same steps for other devices (DVD player/recorder and VCR) which you want to operate using the SRU 5030. You can set the remote control either automatically or manually. Automatically setting the remote control The remote control will now automatically search for the right code for your device. Example of TV: 1 Make sure the TV is switched on and select a channel using the original remote control or the keys on the TV (for example channel 1). The SRU 5030 emits the `switch off TV' signal for all models of TV that are stored in the memory. · If the device is a DVD-player/recorder or video recorder, insert a disk or tape and start playback. 2 Press the TV key to select TV. Press the key until it lights up. 3 Then keep keys 1 and 3 on the SRU 5030 pressed simultaneously for three seconds, until the TV key flashes twice and then remains lit. Instructions for use 4 Press and hold the Standby key of the SRU 5030. English 6 ­ The SRU 5030 now starts emitting all known `TV off ' signals, one by one. Each time a code is sent, the TV key lights up. 5 ­ 6 · When your TV switches off (stand-by), release the Standby key of the SRU 5030 immediately. The SRU 5030 has now found a code that works on your TV. Check if you can operate all functions on your TV with the SRU 5030. If this is not the case, you can redo the automatic setting. The SRU 5030 will then search for a code that works better. After the SRU 5030 has run through all the known codes, the search will stop automatically and the TV key stops flashing. Automatic programming of a TV takes a maximum of 5 minutes. For DVD and VCR this time is 2 minutes. ­ ­ Manually setting the remote control Example of TV: 1 Turn on the TV manually or use the original remote control. Tune in to channel 1. 2 Look up the brand of your TV in the code list at the back of this manual. One or more four-figure codes are shown for each brand. Note the first code. Be careful! There are separate tables for TV, DVD and VCR. On our website www.philips.com/urc you can directly select your device typenumber to find the right code. Make sure you use the codes from the correct table. 3 Press the TV key to select TV. Press the key until it lights up. 4 Keep keys 1 and 3 pressed simultaneously for three seconds until the TV key flashes twice and then remains lit. Instructions for use ­ English 7 5 6 ­ Then enter the code noted in step 2 using the digital keys. The TV key will now flash twice. If the key flashes once for an extended period, the code has not been entered properly or the wrong code has been entered. Start again from step 2. Point the SRU 5030 at the TV and check that it responds as it should. If the TV responds to all of the key commands, the SRU 5030 is ready for use. Do not forget to note your code. If the device does not respond at all, or not to all of the key commands, start again from step 2 and try the next code from the list. · 3. Keys and functions The illustration on page 3 gives an overview of all keys and their functions. 1 y Standby. . . . . . . . . switches TV,VCR or DVD on or off. 2 . . . - teletext on/off ( ); - text mix ( ); - text off ( ); - wide screen TV ( ); - enlarge ( ); - text hold ( ). 3 MENU . . . . . . . . . . . . turns the menu on and off. 4 Cursor keys. . . . . . . cursor up, down, left, right in a menu. 5 A/V . . . . . . . . . . . . . . . switches between external inputs of your equipment. 6 s . . . . . . . . . . . . . . . . . mutes the sound of the TV. 7 - VOL + . . . . . . . . . . . adjusts the TV volume. 8 Digit keys . . . . . . . . . direct choice of channels and other functions. 9 SHIFT . . . . . . . . . . . . for extra functions. When pressed at the same time as a second key, the second key will get another function. All blue labelled keys can be used together with SHIFT. For example: SHIFT + INSTALL installs your TV SHIFT + STORE . . stores TV settings Try out other combinations with the SHIFT-key on your device in order to find out which functions are available. Only functions featured on the original remote control are available. 0 5 . . . . . . . . . . . . . . . . . - red teletext key - rewind (VCR/DVD) 2 . . . . . . . . . . . . . . . . . - index - play (VCR/DVD) 6 . . . . . . . . . . . . . . . . . - blue teletext key - wind (VCR/DVD) 9 . . . . . . . . . . . . . . . . . - green teletext key - stop (VCR/DVD) 0 . . . . . . . . . . . . . . . . . record ; . . . . . . . . . . . . . . . . . . - yellow teletext key - pause (VCR/DVD) Instructions for use ! / . . . . . . . . . . . . . . . . selects between one- and two-figure channel numbers. @ 2 . . . . . . . . . . . . . . . . selects previous programme/channel. # - PROG + . . . . . . . . . selects a previous or following channel. $ OK . . . . . . . . . . . . . . . confirms your selection. % BACK. . . . . . . . . . . . . jumps back one level in the menu or turns off the menu. ^ TV/DVD/VCR . . . . . selects TV, DVD or VCR mode. If you use the (fi) 'memory off' key to get to the next teletext page on your Philips TV, you can press the Subtitle key for this. See also `Troubleshooting'. · If the device does not respond at all, or not to all of the key commands, follow the instructions under `Setting the remote control'. It is possible that you must enter another code for the device. English 8 4. Extra possibilities Adjusting device selection (Mode keys) The SRU 5030 is default set for operating TV, DVD or VCR.You can select the device you wish to operate with the TV, DVD and VCR keys. Each key allows operation of one device only. If desired, you can program the keys to select a different kind of device. For example, if you want to operate a second TV. In the following example you will see how to configure the DVD key for a second TV. 1 2 Switch on the second TV. Press the DVD key to select DVD. Press the key until it lights up. 3 Then keep keys 1 and 6 on the SRU 5030 pressed simultaneously for three seconds, until the DVD key lights up. 4 Press keys 9, 9 and 2 in that order. Instructions for use English 9 5 Press the TV key to select TV. Press the key until it lights up. 6 ­ 7 Press the 1 key. The DVD key flashes twice. The DVD key will now allow you to operate your second TV. Program the SRU 5030 to operate the second TV. See `Setting the remote control'. Adding a function to the remote control If you want to add a function to the SRU 5030, you can contact the Philips service line for Universal Remote Control to ask for the 5-figure code for the extra function. Restoring the original functions of your remote control 1 Keep keys 1 and 6 on the SRU 5030 pressed simultaneously for three seconds, until the mode key (TV, DVD or VCR) flashes twice and then remains lit. 2 ­ Press keys 9, 8 and 1, in that order. The mode key (TV, DVD or VCR) flashes twice. All original functions have now been restored and any extra functions have been deleted. Instructions for use 5. Troubleshooting · ­ · ­ · ­ · ­ · ­ Problem Solution The mode keys (TV and DVD/VCR) blink four times after every key press. The remote control is indicating that its batteries are running low. Replace the old batteries with two new AAA batteries. The device you want to operate does not respond and the mode key (TV, DVD or VCR) does not flash when you press a key. Replace the old batteries with two new AAA batteries. The device you want to operate does not respond but the mode key (TV, DVD or VCR) does flash when a key is pressed. Point the SRU 5030 at the device and make sure that there are no obstructions between the SRU 5030 and the device. The SRU 5030 does not respond properly to commands. Maybe you are using the wrong code. Try programming the SRU 5030 again using another code, which is mentioned under the brand of your device, or reset for automatic search to find the right code. If the device still does not respond, call our helpline. The Teletext keys do not work. Find out whether your TV is equipped with Teletext. Maybe the SRU 5030 has to be adapted to the model of the device. Call our helpline for details. Your brand of device is not in the code list. Try to set the SRU 5030 automatically. See `Automatically setting the remote control'. None of the codes works during manual setting of the remote control. If that is the case, follow the instructions under `Automatically setting the remote control'. English 10 · ­ ­ · ­ · ­ 6. Need help? If you have any questions about the SRU 5030, you can always contact us. You will find our contact details after the code list at the back of this manual. Read this manual carefully before you make a call.You can solve most of the problems yourself. If you cannot find any answers to your problems, write down the details of your device shown in the code list at the back of this manual.This will help our operators to assist you better and more quickly. Look up the numbers of the models in the instructions accompanying the device or on the back of ...