1 1 7 A 2 B 3 4 5 6 8 9 10 EngliSH 6 DEutScH 19 ESpañol FrançaiS 7 italiano 62 nEDErlanDS 76 portuguêS 90 türkçE 105 HS8020, HS8015 6 EngliSH important Read this user manual carefully before you use the appliance and save it for future reference. Danger - Make sure the adapter does not get wet (your adapter may differ from the one shown in the figure). Warning - The adapter contains a transformer. Do not cut off the adapter to replace it with another plug, as this causes a hazardous situation. - This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. - Children should be supervised to ensure that they do not play with the appliance. caution - Never immerse the charger in water nor rinse it under the tap. - Always place and use the charger on a surface that is fluid-resistant. - Use, charge and store the appliance at a temperature between 5°C and 35°C. - Only use the adapter and the charger supplied. - Do not use the shaver or the charger if it is damaged. - If the adapter is damaged, always have it replaced with one of the original type in order to avoid a hazard. EngliSH 7 compliance with standards - This shaver complies with the internationally approved safety regulations and can be safely used in the bath or shower and cleaned under the tap. - This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today. general - The adapter transforms 100-240 volts to a safe low voltage of less than 24 volts. overview (Fig. 1) a 1 2 3 4 5 6 B 7 8 9 10 Shaver Protection cap Shaving unit Shaving conditioner cartridge Shaving conditioner button Charging light On/off button Accessories NIVEA FOR MEN shaving conditioner bottle Charger Cleaning brush Adapter (your adapter may differ from the one shown in the figure) 8 EngliSH getting started charging 1 Put the small plug in the charger and put the adapter in the wall socket. 2 Put the shaver in the charger. , The shaver is being charged. Charge the shaver for 8 hours. Note: Charge the shaver before you use it for the first time or when the charging light indicates that the battery is empty (see section `Charge indications'). Note: A fully charged shaver has a shaving time of up to 30 minutes. charge indications charging - During charging, the charging light lights up green. Battery low - When the battery is low, the charging light lights up red. When you switch off the shaver, the red light slowly goes out. EngliSH Filling the shaving conditioner cartridge 1 Remove the tab of the NIVEA FOR MEN shaving conditioner bottle. 9 2 Turn the cap of the conditioner bottle clockwise (`click'). , The cap moves downwards and the conditioner nozzle appears. Place the nozzle of the conditioner bottle in the filling opening of the conditioner cartridge. Move the bottle up and down approx. 5 times to pump shaving conditioner into the cartridge until you see that the cartridge is full. Do not fill the cartridge beyond the MAX indication. using your shaver Note:Your skin may need 2 to 3 weeks to get accustomed to a new shaving system. 1 Make sure there is sufficient shaving conditioner in the shaving conditioner cartridge. 2 Press the on/off button to switch on the shaver. Make sure the battery is not low (see chapter `Getting started', section `Charge indications'). 10 EngliSH Gently move the shaving unit in circles over your skin and press the shaving conditioner button until there is enough shaving conditioner on your skin for a comfortable shave. - When you release the shaving conditioner button, the appliance stops dispensing conditioner. - Press the shaving conditioner button again to apply more shaving conditioner during shaving to ensure that the shaving unit continues to glide smoothly over your skin. Note:The shaving conditioner button only works when the shaver is switched on. Note:This shaver can be used in a way similar to a razor blade: you can use the shaver on a wet face. Unlike a conventional electric shaver, this appliance has no hair chamber that collects stubble.To prevent stubble from falling on your clothes, apply sufficient shaving conditioner while shaving. 5 Thoroughly clean the shaver after every use (see chapter `Cleaning'). 6 Slide the protection cap onto the shaver to prevent damage. tips for optimal gliding and a smooth shaving result - Gently move the shaver in circles over your skin. - Do not exert too much pressure on the shaver, as this may cause skin irritation. - To ensure proper gliding, apply shaving conditioner regularly. - You can also use the shaver in the bath or shower. EngliSH 11 cleaning and maintenance Clean the shaver after every use. Do not use abrasives, scourers or liquids such as alcohol, petrol or acetone to clean the appliance. Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. Never dry the shaving unit with a towel or tissue, as this may damage the shaving heads. Note:The shaver is watertight and can be cleaned under the tap. 1 Press the on/off button to switch on the shaver. 2 Clean the shaver while it is switched on. There are two ways to clean the shaver: - Rinse the shaving unit under a hot tap for at least 30 seconds. - Immerse the shaving unit in hot water for at least 30 seconds. Switch off the shaver and shake off excess water. Slide the protection cap onto the shaver to prevent damage. Note: If the shaver doesn't shave as well as it used to and you are unable to solve this with the cleaning methods described in this chapter, consult chapter `Frequently Asked Questions' for an extra-thorough cleaning method. 12 EngliSH replacement Shaving conditioner cartridge For hygienic reasons, we advise you to replace the shaving conditioner cartridge twice a year. You can order a new shaving conditioner cartridge from Philips Consumer Care by telephone. To find its phone number, visit www.philips.com and click on `Philips Consumer Care'. 1 Remove the shaving conditioner cartridge from the shaver. 2 Insert the lug at the top of the new shaving conditioner cartridge into the slot in the rim of the shaver (1). Then press the bottom part of the cartridge with your thumb (2) to attach the cartridge to the shaver (`click'). Fill the shaving conditioner cartridge (see chapter `Getting started'). Shaving unit Replace the shaving unit every year for optimal shaving results. Only replace the shaving unit with an HS85 Philips Shaving Unit. 1 Pull the old shaving unit off the shaver. 2 Put the new shaving unit on the shaver. EngliSH 1 niVEa For MEn shaving conditioner bottle Only use NIVEA FOR MEN shaving conditioner bottles. Disposal - Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment. - The rechargeable shaver battery contains substances that may pollute the environment. Always remove the battery before you discard and hand in the shaver at an official collection point. Dispose of the battery at an official collection point for batteries. If you have trouble removing the battery, you can also take the shaver to a Philips service centre. The staff of this centre will remove the battery for you and will dispose of it in an environmentally safe way. Disposal of the rechargeable battery Only remove the rechargeable battery when you discard the shaver. Make sure the battery is completely empty when you remove it. Be careful, the battery strips are sharp. 1 Remove the shaving conditioner cartridge from the shaver. 1 EngliSH 2 Undo the three screws at the back of the shaver. Remove the back panel of the housing with a screwdriver. Remove the rechargeable battery. guarantee and service If you need information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips Customer Care Centre in your country (you find its phone number in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country, go to your local Philips dealer or contact the Service Department of Philips Domestic appliances and Personal Care BV. guarantee restrictions The shaving heads (cutters and guards) are not covered by the terms of the international guarantee because they are subject to wear. The conditioner cartridge is a disposable item and is not covered by the terms of the international guarantee. Frequently asked questions This chapter lists the questions most frequently asked about the shaver. If you cannot find the answer EngliSH 15 to your question, contact the Customer Care Centre in your country. Question Why doesn't the shaving unit glide smoothly over my skin? Why doesn't the shaver shave as well as it used to? Answer You may not have applied enough shaving conditioner. Press the shaving conditioner button until a sufficient amount of NIVEA FOR MEN shaving conditioner has been released. This makes the shaving unit glide smoothly over your skin again. You may not have cleaned the shaver properly. Thoroughly clean the shaver (see chapter `Cleaning and maintenance'). Long hairs may be obstructing the shaving heads. Clean the shaving heads by following the steps of the extra-thorough cleaning method described below. The shaving unit may be damaged or worn. Replace the shaving unit (see chapter `Replacement'). Why doesn't the shaver work when I press the on/off button? The battery may be empty. Recharge the battery (see chapter `Getting started'). Dried shaving conditioner may block the shaving heads in the shaving unit. Clean the shaver thoroughly before you continue shaving (see chapter `Cleaning and maintenance'). You may not have reassembled the shaving unit properly after extra-thorough cleaning. When you reassemble the shaving unit, make sure you turn each guard anticlockwise until it locks into position. 16 EngliSH Answer One of the conditioner holes may be blocked. Rinse or soak the shaving unit. If this does not work, pump shaving conditioner into the shaving conditioner cartridge until conditioner starts to come out of the blocked hole. If this does not work either, try the following method: 1) Switch off the shaver 2) Pull the shaving unit off the shaver 3) Put your finger on the hole that is not blocked 4) Switch on the shaver 5) Press the shaving conditioner button several seconds until conditioner starts to come out of the blocked hole again. You may not have put the shaving heads back into their original holders. One of the shaving heads does not have a shaving conditioner hole in its centre and needs to be placed in a specific holder. Make sure you put the shaving head without conditioner hole in the correct holder.This is the holder that is closest to the on/off button when the shaving unit is assembled on the shaver. Question Why does little shaving conditioner come out of the holes even though there is enough conditioner in the cartridge? Why doesn't any shaving conditioner come out of the holes when I press the shaving conditioner button? The shaving cartridge is almost empty. Refill the shaving conditioner cartridge (see chapter `Getting started'). EngliSH 17 Question I dropped the shaver and the shaving unit fell apart. How should I reassemble the shaving unit? Answer Place the cutters in the shaving head holders with the cutter legs pointing upwards. Place the guards onto the holders (over the cutters) and turn them anticlockwise until they lock into position. One of the guards does not have a shaving conditioner hole in the centre and needs to be attached onto a specific holder. This is the holder that is closest to the on/off button when the shaving unit is assembled on the shaver. If the cutters and the guards have become mixed up, it may take several weeks before optimal shaving performance is restored. You probably did not reassemble the shaving unit properly. Place the cutters in the shaving head holders with the cutter legs pointing upwards. Place the guards onto the holders (over the cutters) and turn them anticlockwise until they lock into position. One of the guards does not have a shaving conditioner hole in the centre and needs to be attached onto a specific holder. This is the holder that is closest to the on/off button when the shaving unit is assembled on the shaver. If the cutters and the guards have become mixed up, it may take several weeks before optimal shaving performance is restored. Extra-thorough cleaning method Make sure the appliance is switched off. 1 Pull the shaving unit off the shaver. Why does the shaver suddenly produce a strange ...