Operating Manual FocusPRO TH6000 Series TM Programmable Thermostat 69-1921ES Quick Reference Card Grasp and pull to see basic operating instructions at a glance. Battery Holder Press down and pull to remove batteries. Batteries should be replaced once a year (see page 17). This manual covers the following models: TH6110D: For 1 Heat/1 Cool systems TH6220D: For up to 2 Heat/2 Cool systems TH6320U: For up to 3 Heat/2 Cool systems (Remove battery holder to find model number) Need Help? For assistance with this product please visit http://yourhome.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502 Read and save these instructions. ® U.S. Registered Trademark. Patents pending. Copyright © 2006 Honeywell International Inc. All rights reserved. FocusPRO TH6000 Series TM Table of contents About your new thermostat Thermostat features................................... 2 Programming at a glance .......................... 3 Quick reference to controls ....................... 4 Quick reference to display ........................ 5 Appendices Battery replacement ................................ 17 In case of difficulty................................... 18 Customer assistance ............................... 20 Accessories/replacement parts ............. .20 5-year limited warranty ............................ 21 Programming & Operation Set time and day ........................................ 6 Select fan setting (auto/on) ....................... 7 Select system setting (heat/cool).............. 8 Using program schedules ......................... 9 Program schedule overrides ................... 12 Auto-changeover (heat/cool) ................... 14 Compressor protection ............................ 15 Adaptive Intelligent RecoveryTM .............. 16 This thermostat is ready to go! Your new thermostat is pre-programmed and ready to go. See page 3 to check settings. CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C). Operating Manual About your new thermostat Congratulations on the purchase of your new Honeywell thermostat. It has been designed to give you many years of reliable service and easy-to-use, push-button climate control. Features · Separately programmable weekday/weekend schedules. · One-touch temp control overrides program schedule at any time. · EnergyStar compliant to greatly reduce your heating/cooling expenses. ® · Large, clear, backlit display is easy to read -- even in the dark. · Displays both room temperature and temperature setting. · Removable battery holder for fast, easy replacement. · Built-in compressor protection. FocusPRO TH6000 Series TM This thermostat is ready to go! Your new thermostat is pre-programmed and ready to go. All you have to do is set the time and day. Then check the settings below and change if needed: 1. 2. 3. 4. Set time and day (required for proper operation) .........................See page 6 Select fan setting (Auto/On): Preset to Auto.................To change, see page 7 Select system setting (Heat/Cool): Preset to Heat ......To change, see page 8 Program schedules: Preset to energy-saving levels while you're at work or asleep (assumes you wake at 6 am, leave at 8 am, return at 6 pm and go to bed at 10 pm) ...............................................................To change, see pages 9- ONE-TOUCH TEMP CONTROL: You can override the program schedule at any time, and manually adjust the temperature (see pages 12-13). Operating Manual Quick reference to controls Digital display (see page 5). Battery holder (see page 17). Temperature Buttons Press to adjust temperature settings (see page 11-13). Function Buttons Press to select the function displayed just above each button. (Functions change depending on the task.) Hold Button Press to override programmed temperature control (see page 13). FocusPRO TH6000 Series TM Quick reference to display screen Current inside temperature In Recovery (see page 16) Current program period Wake/Leave/Return/Sleep (see pages 9-11) Inside Low battery warning (see page 17) Replace Battery In Recovery Current time/day (see page 6) Temperature setting (see pages 11-13) Auxiliary heat (Only for heat pumps with auxiliary heat) System status Heat On/Cool On (If flashing, see page 15) System setting Heat/Cool/Auto/Off/Em Heat (see page 8) Fan setting Auto/On (see page 7) 72 Wake 6:30 Wed Fan Auto AM Set Clock/Day/Schedule (see pages 6 & 11) Set Clock/Day/ Schedule Auxiliary Heat On System Heat 72 Heat Setting Function buttons Press the button beneath each function to view or change settings (functions change depending on the task) Operating Manual Set the time and day Press SET CLOCK/DAY/SCHEDULE, then adjust time 4:30 Set Clock/Day/ Schedule Fan Auto PM System Heat 1. Press the SET CLOCK/DAY/SCHEDULE button, then press s or t to set the clock time. 2. Press the SET DAY button, then press s or t to select the day of the week. 3. Press DONE to save & exit. Note: If the SET CLOCK/DAY/SCHEDULE option is not displayed, press DONE or RUN SCHEDULE. Press SET DAY, then select current day Wed Done Set Day Set Schedule Note: If the display flashes Set Clock, the thermostat will follow your settings for the weekday "Wake" time period until you reset the time and day. 6 FocusPRO TH6000 Series TM Select the fan setting Set Clock/Day/ Schedule Fan Auto System Heat Press the FAN button to select Auto or On. In "Auto" mode (the most commonly used setting), the fan runs only when the heating or cooling system is on. If set to "On," the fan runs continuously. Use this setting for improved air circulation, or for more efficient air cleaning. Set Clock/Day/ Schedule Fan System On Heat 7 Operating Manual Select the system setting Set Clock/Day/ Schedule Fan Auto System Heat Press the SYSTEM button to select: · Heat: Thermostat controls only the heating system. · Cool: Thermostat controls only the cooling system. Set Clock/Day/ Schedule Fan Auto System Cool · Off: Heating and cooling systems are off. · Auto: Thermostat automatically selects heating or cooling depending on the indoor temperature. · Em Heat (only for heat pumps with auxiliary heat): Thermostat controls Emergency and Auxiliary Heat. Compressor is locked out. 8 Note: The Auto and Em Heat system settings may not appear, depending on how your thermostat was installed. FocusPRO TH6000 Series TM Save money by setting program schedules It's easy to program your system for maximum energy savings. You can program four time periods each day, with different settings for weekdays and weekends. WAKE 6:00 am 70 ° Set to the time you awaken and the temperature you want during the morning, until you leave for the day. Set to the time you leave home and the temperature you want while you are away (usually an energy-saving level). Set to the time you return home and the temperature you want during the evening, until bedtime. Set to the time you go to bed and the temperature you want overnight (usually an energy-saving level). 9 LEAVE 8:00 am 62 ° 70 ° RETURN 6:00 pm SLEEP 10:00 pm 62 ° Operating Manual EnergyStar settings for maximum cost savings ® This thermostat is pre-set to use EnergyStar program settings. We recommend these settings, since they can reduce your heating/cooling expenses by as much as 33%. (See next page to adjust times and temperatures of each time period.) ® Heat (Mon-Fri) Wake (6:00 am) Leave (8:00 am) Return (6:00 pm) Sleep (10:00 pm) Cool (Mon-Fri) Heat (Sat-Sun) Cool (Sat-Sun) 70 ° 62 ° 70 ° 62 ° 75 ° 83 ° 75 ° 78 ° 0 [Or cancel period] [Or cancel period] 70 ° 62 ° 70 ° 62 ° [Or cancel period] [Or cancel period] 75 ° 83 ° 75 ° 78 ° FocusPRO TH6000 Series TM To adjust program schedules Set Clock/Day/ Schedule Fan Auto System Cool 1. Press SET CLOCK/DAY/SCHEDULE, then SET SCHEDULE. 2. Press s or t to set your weekday Wake time (Mon­Fri), then press NEXT. Done Set Day Set Schedule 3. Press s or t to set the temperature for this time period, then press NEXT. 4. Set time and temperature for the next time period (Leave). Repeat steps 2 and 3 for each weekday time period. 5. Press NEXT to set weekend time periods (SatSun), then press DONE to save & exit. Note: Make sure the thermostat is set to the system you want to program (Heat or Cool). Note: You can press CANCEL PERIOD to eliminate unwanted time periods (except Wake). Set Schedule 8:00 AM Leave Mon Tue Wed Thu Fri Done 62 Heat Setting CancelPeriod Next Operating Manual Program schedule override (temporary) Press to temporarily adjust temperature. 69 Run Schedule Inside Temporary 6:30 Fan Auto AM 75 System Heat Heat Setting Press s or t to immediately adjust the temperature. This will temporarily override the temperature setting for the current time period. The new temperature will be maintained only until the next programmed time period begins (see page 10). For example, if you want to turn up the heat early in the morning, it will automatically be lowered later, when you leave for the day. To cancel the temporary setting at any time, press RUN SCHEDULE. Press to cancel temporary setting and resume program schedule. Note: Make sure the thermostat is set to the system you want to control (heat, cool or auto). FocusPRO TH6000 Series TM Program schedule override (permanent) Press to permanently adjust temperature. 69 Run Schedule Inside Heat Hold Setting 6:30 Fan Auto AM 75 Press HOLD to permanently adjust the temperature. This will override the temperature settings for all time periods. The "Hold" feature turns off the program schedule and allows you to adjust the thermostat manually, as needed. Whatever temperature you set will be maintained 24 hours a day, until you manually change it, or press RUN SCHEDULE to cancel "Hold" and resume the programmed schedule. System Heat Press to cancel "Hold" setting and resume program schedule. Note: Make sure the thermostat is set to the system you want to control (heat, cool or auto). Operating Manual Auto changeover (heat/cool) Set Clock/Day/ Schedule Fan Auto System Auto Auto Changeover is a feature used in climates where both air conditioning and heating are used on the same day. When the system is set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature. Heat and cool settings must be at least 3 degrees apart. The thermostat will automatically adjust settings to maintain this 3-degree separation (called "deadband"). The 3-degree separation between heating and cooling set temperatures is fixed, and cannot be changed. Press until screen displays "Auto" Note: The Auto system setting may not appear, depending on how your thermostat was installed. FocusPRO TH6000 Series TM Built-in compressor protection 75 Set Clock/Day/ Schedule Inside 6:30 Fan Auto AM 75 Cool Setting This feature helps prevent damage to the compressor in your air conditioning or heat pump system. Damage can occur if the compressor is restarted too soon after shutdown. This feature forces the compressor to wait for a few minutes before restarting. During the wait time, the display will flash the message Cool On (or Heat On if you have a heat pump). When the safe wait time has elapsed, the message stops flashing and the compressor turns on. Cool On System Cool Message flashes until safe restart time has elapsed Operating Manual Adaptive Intelligent Recovery (AIR) TM Adaptive Intelligent Recovery eliminates guesswork when setting your schedule. It allows the thermostat to "learn" how long your furnace and air conditioner take to reach the temperature you want. Just set your program schedule to the time you want the house to reach your desired temperature. The thermostat then turns on the heating or cooling at just the right time to reach your scheduled temperature at your scheduled time. For example: Set the Wake time to 6 am and the temperature to 70°. The heat will come on before 6 am, so the temperature is 70° by the time you wake at 6. Note: When Adaptive Intelligent Recovery is in effect, the thermostat will display "In Recovery". 6 FocusPRO TH6000 Series TM Battery replacement Press and pull to remove Batteries are optional (to provide backup power) if your thermostat was wired to run on AC power when installed. Install fresh batteries immediately when the REPLACE BATTERY warning begins flashing. The warning flashes about two months before the batteries are depleted. Even if the warning does not appear, you should replace batteries once a year, or before leaving home for more than a month. If batteries are inserted within two minutes, the time and day will not have to be reset. All other settings are permanently stored in memory, and do not require battery power. 7 Replace Battery Insert fresh AA alkaline batteries, then ...