El foro DENON RCD-M33
	Ver todas las instrucciones
	Enviar tus instrucciones
	Inscribirse Identificarse
INSTRUCCIONES POR CATEGORIA Electrodomésticos Vídeo & Sonido Auto & Otros vehículos Telefonía Informática Foto & Vídeo Música Material deportivo Casa, bricolaje & Jardín Juegos de vídeo & Programas Joya & Reloj Bebe & Juguete Higiene & Salud Otros

CD RECEIVER RCD-M33 OPERATING INSTRUCTIONS MODE D'EMPLOI INSTRUCCIONES DE OPERACION FOR ENGLISH READERS POUR LES LECTEURS FRANCAIS PARA LECTORES DE ESPAÑOL PAGE 004 ~ PAGE 026 PAGE 027 ~ PAGE 49 PAGINA 050 ~ PAGINA 72 IMPORTANT TO SAFETY WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOIS-TURE. FCC INFORMATION (For US customers) 1. PRODUCT This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this product may not cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired operation. 2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modification not expressly approved by DENON may void your authority, granted by the FCC, to use the product. 3. NOTE This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the product into an outlet on a circuit different from that to which the receiver is connected. · Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for help. SAFETY INSTRUCTIONS 1. Read Instructions ­ All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions ­ The safety and operating instructions should be retained for future reference. 3. Heed Warnings ­ All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions ­ All operating and use instructions should be followed. 5. Cleaning ­ Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. 6. Attachments ­ Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7. Water and Moisture ­ Do not use this product near water ­ for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. 8. Accessories ­ Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. 9. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 10. Ventilation ­ Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 11. Power Sources ­ This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Grounding or Polarization ­ This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. FIGURE A EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR REFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. THE COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL. CAUTION: 1. Handle the power supply cord carefully Do not damage or deform the power supply cord. If it is damaged or deformed, it may cause electric shock or malfunction when used. When removing from wall outlet, be sure to remove by holding the plug attachment and not by pulling the cord. 2. Do not open the top cover In order to prevent electric shock, do not open the top cover. If problems occur, contact your DENON DEALER. 3. Do not place anything inside Do not place metal objects or spill liquid inside the system. Electric shock or malfunction may result. Please, record and retain the Model name and serial number of your set shown on the rating label. Model Name. RCD-M33 Serial No. NOTE: This system uses the semiconductor laser. To allow you to enjoy music at a stable operation, it is recommended to use this in a room of 5 °C (41 °F) ~ 35 °C (95 °F). CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) NEC - NATIONAL ELECTRICAL CODE 13. Power-Cord Protection ­ Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 15. Outdoor Antenna Grounding ­ If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A. 16. Lightning ­ For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 17. Power Lines ­ An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 18. Overloading ­ Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 19. Object and Liquid Entry ­ Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 20. Servicing ­ Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 21. Damage Requiring Service ­ Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into the product, c) If the product has been exposed to rain or water, d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, e) If the product has been dropped or damaged in any way, and f) When the product exhibits a distinct change in performance ­ this indicates a need for service. 22. Replacement Parts ­ When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 23. Safety Check ­ Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 24. Wall or Ceiling Mounting ­ The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 25. Heat ­ The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 2 ENGLISH FRANCAIS ESPAÑOL FRONT PANEL PANNEAU AVANT PANEL FRONTAL !3 !2 !1 !0 o i qw er REAR PANEL PANNEAU ARRIERE PANEL TRASERO t @2 y @1 u @0 @5 @4 @3 !4 !5 !6 !7 !8 !9 3 ENGLISH NOTE ON USE / OBSERVATIONS RELATIVES A L'UTILISATION / NOTAS SOBRE EL USO TABLE OF CONTENTS z x c v b n m , . /0 Main Features ....................................4 Before Using ....................................5 Cautions on Installation ........................5 Connecting the Included Antennas .........5 Connections.......................................6 Part Names and Functions ...............7, 8 Remote Control Unit .....................9, 10 Cautions on Handling Discs ...............11 Listening to Radio Programs .........11 ~ 14 Using the Timer ........................15 ~ 18 /1 Playing CDs ..............................19 ~ 22 /2 Playback ...........................19 Playback Functions ......20 ~ 22 Playing MP3/WMA .....................23 ~ 25 · Normal Playback ........................23, 24 · Various Playback Functions .........24, 25 Auto On Function ..............................25 Troubleshooting ..............................26 Specifications .................................26 · Various · Normal · Avoid high temperatures. Allow for sufficient heat dispersion when installed on a rack. · Eviter des températures élevées Tenir compte d'une dispersion de chaleur suffisante lors de l'installation sur une étagère. · Evite altas temperaturas. Permite la suficiente dispersión del calor cuando está instalado en la consola. · Keep the set free from moisture, water, and dust. · Protéger l'appareil contre l'humidité, l'eau et lapoussière. · Mantenga el equipo libre de humedad, agua y polvo. · Do not let foreign objects in the set. · Ne pas laisser des objets étrangers dans l'appareil. · No deje objetos extraños dentro del equipo. /3 /4 /5 · ACCESSORIES Check that the following parts are included in the package aside from the main unit: qOperating instructions ........................1 wService station list ..............................1 eFM antenna.......................................1 e r rAM loop antenna ..............................1 tRemote control unit (RC-999) ...............1 yR03/AAA batteries ..............................2 t y · Handle the power cord carefully. Hold the plug when unplugging the cord. · Manipuler le cordon d'alimenta-tion avec précaution. Tenir la prise lors du débranchement du cordon. · Maneje el cordón de energía con cuidado. Sostenga el enchufe cuando desconecte el cordón de energía. · Unplug the power cord when not using the set for long periods of time. · Débrancher le cordon d'alimenta-tion lorsque l'appareil n'est pas utilisé pendant de longues périodes. · Desconecte el cordón de energía cuando no utilice el equipo por mucho tiempo. · Do not let insecticides, benzene, and thinner come in contact with the set. · Ne pas mettre en contact des insecticides, du benzène et un diluant avec l'appareil. · No permita el contacto de insecticidas, gasolina y diluyentes con el equipo. 1 MAIN FEATURES 1. Quality power for high quality sound 22W+22W (6 /ohms, 1 kHz, T.H.D. 10%) high quality amplifier and terminals for large speakers. 2. MP3/WMA playback Discs containing MP3 and/or WMA files can be played, and the track and artists names can be displayed during playback. 3. TONE and SDB control TONE control is available for BASS and TREBLE separately and the SDB (Super Dynamic Bass) control enables powerful bass tones when listening at lower volume levels. This unit has Source Direct position to turn off the SDB/TONE. 4. RDS compatible Compatible with various RDS services, including program service name (PS) program type identification (PTY), traffic program identification (TP), clock time (CT) and radio text (RT). (For sets with ventilation holes) · Do not obstruct the ventilation holes. · Ne pas obstruer les trous d'aération. · No obstruya los orificios de ventilación. · Never disassemble or modify the set in any way. · Ne jamais démonter ou modifier l'appareil d'une manière ou d'une autre. · Nunca desarme o modifique el equipo de ninguna manera. 4 ENGLISH 2 BEFORE USING Read the following before using the system. · Before turning on the power Check again that all connections are correct and that there are no problems with the connection cords. Be sure to unplug the power cord before connecting or disconnecting the connection cords. Humming may be produced if this system is set near a TV or other audio equipment. If this happens, try changing the position of the equipment or the connection cords. · Moving the system Be sure to remove CD before moving the system. If a CD is left in the CD receiver, it may be scratched. To prevent short-circuits or damage to the connection cords, always unplug the power cord and disconnect all connection cords to other audio equipment. · Condensation (dew) Condensation (water droplets) may be produced on internal optical lenses or discs in the following cases: · Directly after a heater is turned on. · When the system is in a steamy or humid room. · When the system is moved abruptly from a cold place (room) to a warm room. · Should condensation occur: The signals on the disc cannot be read and the system will not function properly. Remove the disc then let the system set with the power on. The condensation will evaporate in one hour or less, at which time the system will function normally. · Store this instructions in safe place After reading, store this instructions along with the warranty in a safe place. Also fill in the items on the back paper for your convenience. · Illustrations in this manual Note that some of the illustrations used for explanations in this manual may differ from the actual system. 4 CONNECTING THE INCLUDED ANTENNAS Installing the FM indoor antenna Tune in FM station (see page 12), set the antenna so that distortion and noise is minimal, then secure the tip of the antenna in this position using tape or a pin. Installing the AM loop antenna Tune in an AM station (see page 12) and set the antenna as far from the system as possible to keep distortion and noise is minimal. In some cases, it is best to invert the polarities. AM broadcasts cannot be received well if the loop antenna is not connected or if it is set close to metal objects. Assembling the AM loop antenna Connection to the AM loop antenna terminals. AM loop antenna 1 FM antenna 2 3 4 Remove the vinyl tie and take out the connection line. Bend in the reverse direction. a. With the antenna on top any stable surface. Mount b. With the antenna attached to a wall. Connecting an FM outdoor antenna 3 CAUTIONS ON INSTALLATION Note: For heat dispersal, do not install this equipment in a confined space such as a book case or similar unit. Note If good reception cannot be achieved with the included FM antenna, use an FM outdoor antenna. Connect an PAL-type connector to the coaxial cable and connect the antenna to the FM COAX. (75 /ohms) terminal. Selecting a place for the FM outdoor antenna · Set the antenna so that it points towards the broadcast station's transmitting antenna. Behind buildings or mountains, set the antenna in the position at which reception is best, and also try changing the direction of the antenna. · Do not install the antenna under power lines. Doing so is extremely dangerous, as the power line could touch the antenna. · Install the antenna away from roads or train tracks to avoid noise from cars or trains. · Do not install the antenna too high, as it may be hit by lightning. Installation hole Mount on wall, etc. Installing an AM outdoor antenna Connect the signal wire from the AM outdoor antenna to the antenna terminal. Be sure to connect the signal ground wire to the terminal. Also be sure to connect the included AM loop antenna. AM outdoor antenna AM loop antenna Signal ground 5 ENGLISH 5 CONNECTIONS (1) Connecting to Cassette deck NOTE: · This system includes digital circuitry which may cause interference such as color blotching or changes in the color on TVs. If this happens, move the system and the TV as far apart as possible. Connecting the speaker systems Connect the speaker system for the left channel (the left side as seen from the front) to the L terminals, the speaker system for the right channel to the R terminals. Refer to the instructions supplied with the speaker system for details. Be sure to use speaker systems with an impedance of 6 /ohms or greater. Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. Speaker systems (SC-M53) Right Left R IN L CAUTION: · Whenever the power operation switch is in the STANDBY position, the unit is still connected to AC line voltage. Please be sure to unplug the power cord when you leave home for, e.g.,a vacation, etc. CD Recoder etc. Subwoofer Cassette Deck RCD-M33 CD Recoder etc. AM loop antenna Side by side installation OUT LINE OUT IN-2 IN-1 Install the sets as shown in one of these diagrams. In either case, be sure that the CD receiver's ventilation holes are not obstructed. FM antenna Cassette Deck RCD-M33 R IN L OUT LINE CD Recoder etc. Cassette Deck CD receiver (RCD-M33) Power plug AC 120 V, 60 Hz (Plug into a power outlet) Stacking installation System operations Such system operations as the timer and the auto power on functions, as well as remote control operations cannot be performed unless all the RCA pin-plug cords are connected between the units, so be sure to make all the connections properly as shown in the diagram. Be sure to unplug the power cord before changing connections. NOTES: · Do not plug the power cord into the power outlet until all connections are completed. Be sure to interconnect the channels (L to L (white) and R to R (red)) properly, as shown on the diagram. · Insert the plugs securely. Incomplete connections may result in noise. · Be sure to connect the speaker cords between the speaker terminals and the speaker systems with the same polarities ( + to +, ­ to ­ ). If the polarities are switched, the sound at the center will be weak, the position of the different instruments will be unclear, and the stereo effect will be lost. · After unplugging the power cord, wait about 5 seconds before plugging it back in. · Note that setting the connection cords (pin-plug cords) next to the power cords may result in humming or other noise. 6 ENGLISH 6 PART NAMES AND FUNCTIONS (See page 3.) (1) Front Panel i ( 2 /BAND button 2 : CD stop button !1 8 /­ , +/ 9 button (8, 9 : CD automatic search q Power operation switch (ON/STANDBY) · This turns the power for the entire system on and off. · Press this once to turn the power on, then press again to set the power to STANDBY mode. · The LED color changes as follows, according to the condition: During power ON : green During STANDBY : red During TIMER STANDBY: orange The muting mode is set when the main unit's power button is pressed and when the standby mode is canceled from the remote control unit. The power indicator flashes green when in the muting mode, then stops flashing and turns green once the set is in the operational mode. If the indicator is flashing orange (quickly): The protective circuit is activated. If this happens, unplug the power cord to turn the indicator off, then check the input and output terminals on the rear panel. Check in particular for shortcircuiting of the speaker cords. Once all connections have been corrected, plug the power cord. (Wait for at least 10 seconds after turning the power off before turning it back on.) Power is supplied to the RCD-M33 even when the power is in the standby mode (The clock is displayed in the clock display mode.) Remote sensor · When operating the remote control unit, point it at this sensor. e PHONES (headphones jack) · Plug the headphones into this jack. · No sound is produced from the speakers when headphones are plugged in. FUNCTION button · Use this to select the input (function). · The input changes in the following order each time this button is pressed: CD TUNER TAPE AUX BAND : TUNER band button) · In CD function, press this button to stop playback. · In TUNER function, each time this button is pressed, the band and FM reception mode change as follows: FM AUTO FM MONO AM r o t y Display · Refer to page 8. 1/ 3 (play/pause) button SDB (Super Dynamic Bass)/TONE button · Press this button to select the preferred sound of TONE CONTROL/SDB. Each time this button is pressed, the display changes as follows: SDB BASS TREBLE S.DIRECT reverse/forward button +,­ : TUNER up/down button) · Use the 8 and 9 buttons to move to the beginning of a specific track while in CD function. · Use the +/­ button to select radio stations while in TUNER function. · In TUNER function, press the 2 /BAND and + buttons at the same time to change the Preset mode, the 2 /BAND and ­ buttons at the same time to change the Tuning mode. · Use the +/­ button when you adjust tone control (BASS or TREBLE) and you select menu function (display, time, timer, or set up). !2 5 (open/close) button · Press this button to start playing a disc. When the disc tray is closed, playback begins when this button is pressed. · When pressed in STANDBY mode, the power automatically turns on and playback begins (Auto On function). Press this button again to stop playback temporarily. VOLUME control · Use this to adjust the overall volume (Rotary Encorder System). · The volume increases when the control is turned clockwise (,) and decreases when it is turned counterclockwise (.). · The volume increases and decreases in 35 steps from the minimum (VOLUME 00) to the maximum (VOLUME MAX). NOTE: · Care must be taken when you adjust the volume as the CD receiver is equipped with an electronic volume control. Turn the VOLUME control slowly referring to the indication on the display to adjust the volume. u · You can switch the SDB on/off by using the +/­ (up/down) button. · BASS and TREBLE can be adjusted by using the +/­ (up/down) button. · When you select S.DIRECT (Source Direct), SDB/TONE is switched off, and the sound characteristic becomes flat. · SDB can be controlled powerful bass tones when listening at lower volume levels. NOTE: · The SDB should be deactivated when listening at higher volume levels. Excessive bass at high volume levels will result in a distorted sound and may cause damage to your set and speaker system. · Press this button to open and close the disc tray. · When pressed once, the disc tray opens out, and when pressed again, the disc tray closes. If a disc is loaded, the total number of tracks and total playing time of the disc are displayed several seconds after the disc tray is closed. · When pressed in STANDBY mode, the CD receiver's power turns on. Disc tray · Load discs here. !3 w !0 MENU/ SET button · When pressed in the standby mode, the standby mode is switched (the clock display is switched on and off). · When pressed while the clock is displayed, the manual time setting mode is set. (This cannot be set while the clock is displayed in the standby mode.) · Switches the display of the timer setting menu on and off. · When the function is set to FM and the CT tuning mode is set, the mode switches to the auto time setting mode. · When the function is set to TUNER and an FM station is being received, if pressed for more than 1 second, the display switches to the AUTO PRESET menu. 7 ENGLISH (2) Rear Panel (3) Display !4 !5 !6 !7 AUX IN (analog input) jacks · This is an input terminal. AUX OUT (analog output) jacks · This is an output terminal for recording. FM antenna terminal (ANTENNA TERMINAL FM) · Connect the FM antenna here. Digital output jack (DIGITAL OPTICAL OUT) · Digital data is output in optical form from this jack. Speaker terminals (SPEAKERS) · Use these to connect the speakers. System connectors (SYSTEM CONNECTOR 1 and 2) · When connecting the cassette deck, connect these connectors to system connectors on other system components. (Use the system cords included with the other components.) AC OUTLET · When using in combination with the cassette deck, connect to the AC outlet on the CD receiver (RCD-M33) or one of the other components (100W MAX). Power cord · Plug this cord into a wall power outlet. MONO OUT terminal (SUB WOOFER) · Connector jack for subwoofer with builtin amplifier (super woofer), etc. AM antenna terminal (ANTENNA TERMINAL AM) · Connect the AM antenna here. TAPE OUT (analog output) jacks · This is an output terminal for recording. TAPE IN (analog input) jacks · This is an input terminal. q we r t y u i o !0 !1 !2 q Segment